To choose a multihead weigher, match the product, target portion and discharge arrangement before comparing head counts. The right configuration must handle the material consistently and deliver it into the pouch at your required accepted output.
A multihead weigher measures portions in separate hoppers and selects a combination for discharge. That principle explains why product distribution, hopper suitability and the path to the pouch matter alongside the weighing controls. Use the questions below to turn a machine quotation into a proposal you can verify.
Describe the product as it reaches the weigher
Give suppliers representative samples and describe the product at the point of weighing. Include typical piece dimensions, variation in piece size, bulk density where known, and whether the surface is dry, wet or sticky. Describe temperature or other relevant conditions rather than naming the product alone.
For fragile products, define what counts as unacceptable damage. Ask to compare the condition of the incoming material with the product collected after discharge. A weight result alone cannot establish that the handling process preserves saleable quality.
Sticky or difficult products may need a specialised feed arrangement or contact-part design. Fragile products may need a gentler transfer path. These are reasons to investigate an application-specific configuration, rather than assume a standard dry-product machine will work.
Include normal product variations in the trial brief. If the supplier receives only the easiest batch, the result will leave other operating conditions unresolved.
Specify weight and volume together
List each target pack weight with the product and pouch format. Also describe the volume the portion occupies. A light, bulky product and a dense granule can have the same pack weight but need different handling space.
Hopper capacity and weighing range describe different limits. Ask the supplier to identify the proposed hopper size, usable application range and any restrictions for your material. Do not treat the total pack weight as the amount that every individual hopper must contain.
Use this brief when comparing configurations.
| Selection input | What you provide | What the proposal should explain |
|---|---|---|
| Portion requirements | Target weights and relevant product variations | Which combinations will be tested and under what conditions |
| Product handling | Piece size, bulkiness, flow and damage criteria | Feed method, contact parts and hopper arrangement |
| Pouch delivery | Opening dimensions and available filling space | Outlet, transfer path and bagger interface |
| Production requirement | Accepted packs over a stated period | Complete-line assumptions and remaining trial work |
Swipe the table to view all columns.
If the recipe contains several ingredients, state whether they arrive premixed or must be combined on the machine. Ask how the proposed system will verify the required composition. Achieving the total pack weight does not by itself demonstrate the correct ingredient ratio.

Evaluate the feeding system before head count
Combination weighing depends on product being available in suitable portions across the weighing hoppers. Ask how the infeed, distribution system and individual feed paths will handle your material. Watch for uneven distribution or retained product during the trial.
More heads can expand the combinations available to the control system, but that does not establish the result for your application. Product flow, portion size and the discharge sequence still matter. Ask suppliers to explain the proposed head count in relation to the actual product and required output.
Compare configurations using the same trial conditions. A different product, target weight or feed arrangement can make two quoted performance figures unsuitable for direct comparison.
For low target weights or large individual pieces, request results using the actual size distribution. The weighing system selects from available portions; it cannot turn an unsuitable product sample into evidence for a different one.
Check discharge into the pouch
Ask for a layout showing the weigher outlet, transfer components and pouch machine below it. Confirm the available height, support arrangement and access for operators and maintenance. Include the product supply equipment in the space assessment.
During the combined trial, observe the dose from hopper discharge to pouch entry. Record product remaining in the path, material outside the pouch and any damage introduced during transfer. A successful collection into an open container leaves the pouch interface to be demonstrated.
Agree how the machines communicate readiness, discharge completion and faults. Ask which supplier is responsible for the mechanical connection and control interface, especially when equipment comes from different sources.
Keep weighments per minute separate from accepted sealed pouches per minute. The pouch machine and transfer arrangement must receive and process the portions. Compare the output of the assembled line under stated conditions.

Review cleaning and product changes
Ask to see how operators remove, clean and reinstall the relevant product-contact parts. Include access around the installed machine, rather than judging access from a freestanding demonstration.
State your cleaning method and environment. Request confirmation that the quoted construction and components are suitable. Stainless-steel surfaces alone do not establish washdown suitability or compatibility with a particular cleaning process.
For frequent changes, record which parts and recipes must change and how setup is checked afterward. Ask what procedures, training and spare parts are included in the proposal. These details affect how readily your team can maintain the tested operating conditions.
Compare documented trial results
Agree on the product, pouch, target weight and acceptance criteria before the trial. Keep the test conditions attached to every quoted accuracy or output figure. Performance specifications may depend on product shape, density and target weight.
Request a report containing:
- The product sample, batch and relevant condition at weighing.
- The machine configuration, hopper size, feed system and recipe.
- Individual portion measurements and the measurement method.
- Trial duration, operating rate, accepted packs and rejected packs.
- Observed damage, retained product, stops and manual intervention.
- The equipment included in the trial and any interface work still outstanding.
Review individual results as well as the average. An average near target can conceal a wide spread of filling variation. Also distinguish measured portions from finished-pack net weights when the trial includes packaging.
If a demonstration uses a substitute product or omits the pouch machine, record that limitation. Decide what additional evidence is needed before accepting the proposed arrangement. Do not extend one successful trial to untested products or formats automatically.

Questions to settle before placing an order
Is a higher head count always the better choice
No. Ask how each proposed configuration meets your product, portion and output requirements. Choose based on comparable trial evidence and the full installation scope, including feeding and discharge.
Can one machine handle sticky and fragile products
Some applications need specialised configurations. Require the supplier to identify the intended feed and handling arrangements and demonstrate them with representative samples. Do not rely on a broad product-category claim.
Should the weigher and bagger be selected together
Confirm their interfaces together before finalising the purchase. If you shortlist them separately, keep the combined discharge trial, support layout and control responsibilities as explicit purchase conditions.
Prepare a weighing brief for Huapack
Share your product samples, portion weights, pouch dimensions and accepted-output requirement with Huapack Machinery. Include product variations, damage criteria and cleaning needs. Ask which weigher and pouch packing arrangement should be evaluated and what a representative combined trial will cover.






